There is some level of water loss that is to be expected from a swimming pool or a spa in the course of its use. Normal water loss from the structure usually happens in three major ways, that is, through evaporation, splash out, and backwashing the filters. For people who live in hot regions, the amount of water lost to evaporation can be substantial. Here are facts regarding Queen Creek pool service.
As water is lost through the methods named above, it is advisable to add a minimum of two inches of water per week to the structure. The need to add over two inches however, may indicate the existence if a leak. This is especially true if there is no other reason for the change in the speed of loss of water.
For instance, it is to be understood that water evaporation may change depending on the season. Also, if the usage of the pool has increased in the recent past, then it may mean that water loss will also increase. However, if none of these has happened yet the loss of water seems to happen at a faster rate, then it may be time to be suspicious.
Before one decides to go further to contact a local pool technician, it is vital to confirm the suspicions one has. Several techniques can be employed to ascertain if indeed a leak actually exists. To confirm the presence of a leak, one should begin by inspecting the obvious. For example, one should make sure the leakage is not located at the equipment.
To make sure there is no leakage, one ought to have a close look at the filter, pump, pipe valves, and heater. One also has to check the ground surrounding the structure to make sure it is dry. The individual should walk around the pool/spa to check for any sunken areas or those that have been eroded. If nothing is out of place, it is time to move to the next step.
Another method that one can use to determine if their structure is leaking is by marking the level of the water in the structure at the skimmer. This can be done using a pencil, tape, or grease. One should then give the pool a period of 24 hours before coming back to check the new level of the water.
A normal structure should lose a quarter of an inch per day. If the drop in water level is more than a quarter an inch, then it may be indicative of the existence of a leak. One can also use a bucket filled with water to the same level as the level of water inside the structure. The bucket should then be placed on the steps that are used to access the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
As water is lost through the methods named above, it is advisable to add a minimum of two inches of water per week to the structure. The need to add over two inches however, may indicate the existence if a leak. This is especially true if there is no other reason for the change in the speed of loss of water.
For instance, it is to be understood that water evaporation may change depending on the season. Also, if the usage of the pool has increased in the recent past, then it may mean that water loss will also increase. However, if none of these has happened yet the loss of water seems to happen at a faster rate, then it may be time to be suspicious.
Before one decides to go further to contact a local pool technician, it is vital to confirm the suspicions one has. Several techniques can be employed to ascertain if indeed a leak actually exists. To confirm the presence of a leak, one should begin by inspecting the obvious. For example, one should make sure the leakage is not located at the equipment.
To make sure there is no leakage, one ought to have a close look at the filter, pump, pipe valves, and heater. One also has to check the ground surrounding the structure to make sure it is dry. The individual should walk around the pool/spa to check for any sunken areas or those that have been eroded. If nothing is out of place, it is time to move to the next step.
Another method that one can use to determine if their structure is leaking is by marking the level of the water in the structure at the skimmer. This can be done using a pencil, tape, or grease. One should then give the pool a period of 24 hours before coming back to check the new level of the water.
A normal structure should lose a quarter of an inch per day. If the drop in water level is more than a quarter an inch, then it may be indicative of the existence of a leak. One can also use a bucket filled with water to the same level as the level of water inside the structure. The bucket should then be placed on the steps that are used to access the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
About the Author:
Get excellent tips on how to pick a Queen Creek pool service company and more info about a reliable company at http://www.neptunepoolsaz.com right now.
0 comments:
Post a Comment